Residential · Myrtle Beach, SC
A pool screen enclosure should block bugs and wind-blown debris, stay tight in storms, and look clean from every angle. Myrtle Beach Screens has served Myrtle Beach since 2015 with aluminum screen enclosure installation, rescreening, and structural repairs built around proper anchoring, straight lines, and long-lasting mesh.
We start by measuring the deck and cage footprint, checking slab edges, pavers, and existing footers, and confirming door swings and equipment clearances. On new builds, we lay out post locations, snap reference lines, and plan roof pitch so water sheds away from the pool and house. For repairs, we inspect for loose base tracks, wall channel separation, bent kick plates, and fastener pull-out, then document what can be tightened versus what must be replaced. Expect a clear scope that covers framing, hardware, and screening so there are no surprises mid-project.
Coastal sun, salt air, and wind load demand the right materials and a tight finish. We build with aluminum framing and track systems, using corrosion-resistant fasteners where needed, then stretch and spline screen evenly to prevent sagging, wrinkles, and noisy panels. We rescreen and patch with pool and patio mesh options such as 18x14 fiberglass, 18x16, no-see-um mesh, and pet-resistant screen, matched to the opening size and use case. Corners, doors, and roof transitions get extra attention so the enclosure stays square, doors latch cleanly, and the final look is straight, smooth, and consistent.
Customers in Myrtle Beach choose us because we treat the pool screen enclosure as a structure, not just screen replacement. You get a licensed and insured contractor that shows up on schedule, protects the pool area, and communicates clearly about what we find and what it costs to fix. We handle full installs, storm damage repairs, rescreening, door replacements, and hardware swaps, including hinges, latches, closers, rollers, and turnbuckles where applicable. Our crews focus on clean lines, tight screen tension, and solid anchoring so the enclosure performs through wind, rain, and daily use.
To close out the job, we walk the enclosure with you and check doors for smooth operation, latch alignment, and proper closing tension. We verify screen tension, confirm there are no gaps at corners, base rails, or around door frames, and clean up all cut-offs, old spline, and fasteners. You receive a written estimate up front, a clear description of materials installed, and care guidance for rinsing salt, keeping tracks clean, and spotting early hardware corrosion. If something looks off after the first few days of use, we want the call, we stand behind our workmanship and we handle adjustments quickly.
Yes. We provide a free written estimate after evaluating the enclosure, measuring, and confirming the best material and scope for the job.
Yes. We replace torn mesh, re-secure loose panels, repair damaged door hardware, and address common wind-failure points like pulled spline and bent frame members.
Yes. We can replace individual panels when the surrounding mesh and frame are in good condition, and we will match material and color as closely as practical.
We work on pool enclosures, screen rooms, lanais, porches, patios, and screened entries, including rescreening, repairs, and door installation or replacement.
Yes. Myrtle Beach Screens is a licensed and insured screening contractor.
If your pool screen enclosure is sagging, letting in mosquitoes, rattling in the wind, or showing bent framing after a storm, the fix is rarely just one torn panel. Myrtle Beach Screens installs new enclosures and performs targeted pool cage repairs, rescreening, and door and hardware work with an emphasis on straight framing, tight screen tension, and corrosion-resistant fastening for coastal conditions.
A properly built pool screen enclosure starts with accurate layout and a solid base connection. We measure openings, confirm post locations, and review any existing channels, kick plates, and attachment points to determine what can be repaired and what should be replaced. When we rescreen, we remove failed mesh and spline, inspect rails and corners for movement, and rebuild screen panels so they sit flat with even tension across the frame.
Material choice matters in a salty, high-UV environment. We commonly install fiberglass mesh in 18x14 or 18x16 for balanced visibility and strength, no-see-um mesh for finer insect control, and pet-resistant screen for higher abuse areas near doors. For structural issues, we address loose tracks, pulled fasteners, and misaligned doors that create gaps and premature tearing. The goal is a pool screen enclosure that stays tight, closes correctly, and looks uniform from panel to panel.
From the first visit to final walkthrough, you get clear communication and a clean jobsite. We confirm door operation, latch alignment, and screen fit at corners and transitions, then leave you with a straightforward maintenance plan to extend the life of your enclosure. For installation or repair in Myrtle Beach, request a free written estimate and get your pool area back to comfortable, bug-controlled use.
Call now or send a request and we will reach out within one business day to schedule your free, no-obligation estimate in Myrtle Beach. We assess the project, review the details, and give you a written quote before any work starts, so you know exactly what to expect.
Prefer to write? Contact us or head back to the home page.